ZCM1000 / M1000 automatic adhesive tape dispenser with programmable cut length

  • Electric dispenser for single or double-sided tapes
  • 1 programmable cutting length from 20 to 999 mm
  • Reliable, robust, easy to use
  • 76 mm, 35 mm or 25 mm cores

Quote

Close

Overview

          Compatible adhesive tapes with the ZCM1000 / M1000

    The ZCM1000, also known as the M1000, is an automatic dispenser compatible with the following adhesives:

     

    It features three hubs accommodating cores of 76 mm, 35 mm, or 25 mm.

     

    The ZCM1000 accepts adhesive tape rolls up to 180 mm wide. For use with larger diameter rolls, employ the TDSTAND03 external support, an accessory for the automatic dispenser suitable for cutting large rolls.

     

    Caution:

    This device is not compatible with VHB tapes and 100% acrylic foam adhesives. For cutting foam adhesive tapes, prefer the RT7000 automatic dispenser.

          Description of the M1000 / ZCM1000 automatic dispenser

    Here is a diagram summarizing the main controls of the device:

     

          Operating instructions for the M1000

    Several operation modes are available:

     

    • In automatic mode

    Follow these steps:

    1. Plug in the power cord. Set the ON/OFF switch to ON (the display shows 20).
    2. Place the roll in its position and adhere the tape to the top of the drive roller. Press the ADVANCE button (down arrow) until the tape comes out the front of the cassette.
    3. Grasp the tape and gently pull it (if the tape has not loaded correctly, fold the tape halfway or into a triangle shape, then adhere it to the drive roller and repeat the procedure). Press the CUT button (scissors) to cut the end of the tape.
    4. Set the cut length by pressing the CM or MM buttons. Adjust the pressure on the tape with the pressure button: usually set to S, unless the tape loops, then switch it to H.
    5. Once all adjustments are made, press the AUTO button. As soon as the first cut tape is grasped, it releases another of the same size, thanks to a photoelectric cell detection.

     

    • In semi-automatic mode
    1. Plug in the power cord. Set the ON/OFF switch to OFF. By pressing the AUTO button, the device produces a piece of tape of the displayed length and cuts it. This operation repeats with each button press.
    2. When using a long length, hold the end of the tape during its exit.

     

    • In unrolling mode
    1. Press the ADVANCE button until the tape comes out and cut it with the CUT button.
    2. When using a long length, hold the end of the tape during its exit.

     

    • Changing the roll

    Press the REVERSE button (up arrow) to remove the tape and the roll.

     

    • In case of jamming

    In the event of a jam, press the REVERSE button to remove the tape. Then remove the cutting unit and check that no tape has stuck to the blades or rollers.

          Cleaning and safety precautions for the M1000 / ZCM1000

    Caution: These dispensers are cutting tools and contain blades. Take necessary precautions to avoid contact with the blades during use. NEVER insert fingers into the cutting block. Any disassembly or maintenance of these dispensers should be performed by qualified personnel.

     

    It is recommended to clean the device with a dry cloth, avoiding detergents or aerosols.

     

    Regularly check for glue residue on the blades, as this can hinder the device's proper functioning. If necessary, clean with silicone oil, ensuring safety to avoid cuts.

     

    If storing the device for an extended period, ensure that the tape does not remain on the rollers by pressing the REVERSE button.

     

    In case of jamming, do not use a cutter and especially do not insert it into the blade holder slot, as this could damage the silicone drive disks (which can be replaced and ordered from ADEZIF).

     

          Technical data table

    Technical information 
    ColorCream white
    Dimensions (L x P x H)137 x 218 x 150 mm
    Weight2.4 kg
    Tape WidthFrom 7 to 50 mm
    External Roller DiameterMax 180 mm
    Cut LengthFrom 20 to 999 mm
    Core Size3-in-1 hub: 25, 35, 76 mm
    Operating ModesAutomatic or semi-automatic
    Power Consumption18 W
    Power SupplyAC 230 V - 50/60 Hz

    Customers who viewed this page also viewed